Teltonika-BLE - Revision history

ARSLAN: /* Direct BT connection (no adapter) */

2026-03-04T10:27:02Z

Direct BT connection (no adapter)

← Older revision		Revision as of 13:27, 4 March 2026
Line 4:		Line 4:

	= Direct BT connection (no adapter) =		= Direct BT connection (no adapter) =
	Currently, '''the TD-BLE, DU-BLE and TL-BLE are compatible with certain Teltonika models''' (see the list on the last page of this document; note that it is not definitive; for a more precise list, please, contact Teltonika’s tech support).		Currently, '''the TD-BLE, TW-BLE (TD-150-BLE) DU-BLE and TH-BLE are compatible with certain Teltonika models''' (see the list on the last page of this document; note that it is not definitive; for a more precise list, please, contact Teltonika’s tech support).

	* Up to 4 sensors can be connected to the majority of different Teltonika models via Bluetooth		* Up to 4 sensors can be connected to the majority of different Teltonika models via Bluetooth
Line 18:		Line 18:

	== Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings) ==		== Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings) ==
	In the Teltonika configurator, go to the '''Bluetooth''' tab first. Make sure that everything is configured as shown on the ~~figure~~ below		In the Teltonika configurator, go to the '''Bluetooth''' tab first. Make sure that everything is configured as shown on the screenshot below:

	[[File:Photo 5418063427176959105 x.jpg\|frameless\|408x408px]]		[[File:Photo 5418063427176959105 x.jpg\|frameless\|408x408px]]
Line 40:		Line 40:


	Further below you have 4 '''Connection slots''' to pair up to 4 sensors (those can be any TD, DU or TH sensors). Click on the '''Advanced''' button and then '''enter the MAC address''' of the sensor.		Further below you have 4 '''Connection slots''' to pair up to 4 sensors (those can be any TD, TW, DU or TH sensors). Click on the '''Advanced''' button and then '''enter the MAC address''' of the sensor.


Line 56:		Line 56:
	- “escort fuel” for TD-BLE,		- “escort fuel” for TD-BLE,

	- “escort luminosity” or “escort temperature” for TH-BLE, ~~“Escort_DU-BLE_Angle_sensor” for DU-BLE~~		- “escort luminosity” or “escort temperature” for TH-BLE,

			- “Escort DU_BLE” for [https://drive.google.com/file/d/1xQgTjlbQ8W2oOb8Owpj2Jr_U7xh4-2a0/view DU-BLE]

			- "Escort_TD_150_BLE" for [https://drive.google.com/file/d/1_wiyNRlUvUn0JarXYwcJNpeahZNlH1Fw/view TD-150-BLE] (TW-BLE)


Line 83:		Line 86:
	== System settings (Codec 8 Extended) ==		== System settings (Codec 8 Extended) ==
	In the '''System''' tab, click on the '''Codec 8 Extended''' option.		In the '''System''' tab, click on the '''Codec 8 Extended''' option.

ARSLAN: /* Common issues and how to resolve them */

2026-03-04T10:21:15Z

Common issues and how to resolve them

← Older revision		Revision as of 13:21, 4 March 2026
Line 238:		Line 238:

	== BLE Fuel Level missing in I/O ==		== BLE Fuel Level missing in I/O ==
	'''If you cannot find the BLE Fuel Level parameter in the I/O tab''' of a newer version of Teltonika configurator, please, use one of the old ones available via the links below in the "Compatibility list" section of this article.		'''If you cannot find the BLE Fuel Level parameter in the I/O tab''' of a newer version of Teltonika configurator, please, use one of the old ones available via the links below in the "[[Teltonika-BLE#Compatibility list\|Compatibility list]]" section of this article.

	The links allow you to download a compressed file with an old FW version (you don’t need to install it onto the tracker) and an older version of the configurator for different tracker models.		The links allow you to download a compressed file with an old FW version (you don’t need to install it onto the tracker) and an older version of the configurator for different tracker models.
Line 249:		Line 249:
	'''Before installing a BLE sensor and a tracker, you need to properly configure the BLE Scan sessions as indicated [[Teltonika-BLE#Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings)\|above]]) and check the stability of the Bluetooth connection to select the best spot to install the GPS tracker/gateway (or BLE-RS485-RS232 adapter) to minimize the risks of connection losses happening in the future. Also, be sure to orient the antennas of the devices as per recommendations provided [[Teltonika-BLE#Antenna orientation\|above]].'''		'''Before installing a BLE sensor and a tracker, you need to properly configure the BLE Scan sessions as indicated [[Teltonika-BLE#Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings)\|above]]) and check the stability of the Bluetooth connection to select the best spot to install the GPS tracker/gateway (or BLE-RS485-RS232 adapter) to minimize the risks of connection losses happening in the future. Also, be sure to orient the antennas of the devices as per recommendations provided [[Teltonika-BLE#Antenna orientation\|above]].'''

	To determine if the connection between the Bluetooth transmitter of the sensor and the Bluetooth receiver is stable or not, you should use the RSSI parameter. When you search for a place to install the GPS tracker, you should calculate the average RSSI (Received Signal Strength Indicator) by taking into account the 10 or more measurements of the RSSI taken over the course of 2-3 minutes while the engine of the vehicle is running and all electronics inside the cab and around the vehicle are switched on.		To determine if the connection between the Bluetooth transmitter of the sensor and the Bluetooth receiver is stable or not, you should use the RSSI parameter. When you search for a place to install the GPS tracker, [[Teltonika-BLE#RSSI check\|you should calculate the average RSSI]] (Received Signal Strength Indicator) by taking into account the 10 or more measurements of the RSSI taken over the course of 2-3 minutes while the engine of the vehicle is running and all electronics inside the cab and around the vehicle are switched on.

	The reason why the RSSI should be taken as the average value is that the RSSI itself is a dynamic parameter, its value changes constantly. This average value must be within the connection stability range.		The reason why the RSSI should be taken as the average value is that the RSSI itself is a dynamic parameter, its value changes constantly. This average value must be within the connection stability range.

ARSLAN: /* Data losses */

2026-03-04T10:16:46Z

Data losses

← Older revision		Revision as of 13:16, 4 March 2026
Line 247:		Line 247:
	If there is a connection loss, after several attempts to collect the data (the '''Scan retries until error''' setting in the Bluetooth 4.0 tab) the tracker will transmit the error '''code 3000/300 in the temperature io'''. The level value will be transmitted as the last reading transmitted by the sensor if it was connected via the BLE base, or '''0\-4\65532''' in the fuel data.		If there is a connection loss, after several attempts to collect the data (the '''Scan retries until error''' setting in the Bluetooth 4.0 tab) the tracker will transmit the error '''code 3000/300 in the temperature io'''. The level value will be transmitted as the last reading transmitted by the sensor if it was connected via the BLE base, or '''0\-4\65532''' in the fuel data.

	Before installing a BLE sensor and a tracker, you need to properly configure the BLE Scan sessions as indicated ~~in this article~~ [[Teltonika-BLE#Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings)\|above]]) and check the stability of the Bluetooth connection to select the best spot to install the GPS tracker/gateway (or BLE-RS485-RS232 adapter) to minimize the risks of connection losses happening in the future. Also, be sure to orient the antennas of the devices as per recommendations provided [[Teltonika-BLE#Antenna orientation\|~~in this article~~ above]].		'''Before installing a BLE sensor and a tracker, you need to properly configure the BLE Scan sessions as indicated [[Teltonika-BLE#Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings)\|above]]) and check the stability of the Bluetooth connection to select the best spot to install the GPS tracker/gateway (or BLE-RS485-RS232 adapter) to minimize the risks of connection losses happening in the future. Also, be sure to orient the antennas of the devices as per recommendations provided [[Teltonika-BLE#Antenna orientation\|above]].'''

	To determine if the connection between the Bluetooth transmitter of the sensor and the Bluetooth receiver is stable or not, you should use the RSSI parameter. When you search for a place to install the GPS tracker, you should calculate the average RSSI (Received Signal Strength Indicator) by taking into account the 10 or more measurements of the RSSI taken over the course of 2-3 minutes while the engine of the vehicle is running and all electronics inside the cab and around the vehicle are switched on.		To determine if the connection between the Bluetooth transmitter of the sensor and the Bluetooth receiver is stable or not, you should use the RSSI parameter. When you search for a place to install the GPS tracker, you should calculate the average RSSI (Received Signal Strength Indicator) by taking into account the 10 or more measurements of the RSSI taken over the course of 2-3 minutes while the engine of the vehicle is running and all electronics inside the cab and around the vehicle are switched on.

ARSLAN: /* BLE Fuel Level missing in I/O */

2026-03-04T10:11:32Z

BLE Fuel Level missing in I/O

← Older revision		Revision as of 13:11, 4 March 2026
Line 235:		Line 235:


	= BLE Fuel Level missing in I/O =		= Common issues and how to resolve them =

			== BLE Fuel Level missing in I/O ==
	'''If you cannot find the BLE Fuel Level parameter in the I/O tab''' of a newer version of Teltonika configurator, please, use one of the old ones available via the links below in the "Compatibility list" section of this article.		'''If you cannot find the BLE Fuel Level parameter in the I/O tab''' of a newer version of Teltonika configurator, please, use one of the old ones available via the links below in the "Compatibility list" section of this article.

Line 245:		Line 247:
	If there is a connection loss, after several attempts to collect the data (the '''Scan retries until error''' setting in the Bluetooth 4.0 tab) the tracker will transmit the error '''code 3000/300 in the temperature io'''. The level value will be transmitted as the last reading transmitted by the sensor if it was connected via the BLE base, or '''0\-4\65532''' in the fuel data.		If there is a connection loss, after several attempts to collect the data (the '''Scan retries until error''' setting in the Bluetooth 4.0 tab) the tracker will transmit the error '''code 3000/300 in the temperature io'''. The level value will be transmitted as the last reading transmitted by the sensor if it was connected via the BLE base, or '''0\-4\65532''' in the fuel data.

	Before installing a BLE sensor and a tracker, you need to properly configure the BLE Scan sessions as indicated in this article above) and check the stability of the Bluetooth connection to select the best spot to install the GPS tracker/gateway (or BLE-RS485-RS232 adapter) to minimize the risks of connection losses happening in the future. Also, be sure to orient the antennas of the devices as per recommendations provided in this article above.		Before installing a BLE sensor and a tracker, you need to properly configure the BLE Scan sessions as indicated in this article [[Teltonika-BLE#Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings)\|above]]) and check the stability of the Bluetooth connection to select the best spot to install the GPS tracker/gateway (or BLE-RS485-RS232 adapter) to minimize the risks of connection losses happening in the future. Also, be sure to orient the antennas of the devices as per recommendations provided [[Teltonika-BLE#Antenna orientation\|in this article above]].

	To determine if the connection between the Bluetooth transmitter of the sensor and the Bluetooth receiver is stable or not, you should use the RSSI parameter. When you search for a place to install the GPS tracker, you should calculate the average RSSI (Received Signal Strength Indicator) by taking into account the 10 or more measurements of the RSSI taken over the course of 2-3 minutes while the engine of the vehicle is running and all electronics inside the cab and around the vehicle are switched on.		To determine if the connection between the Bluetooth transmitter of the sensor and the Bluetooth receiver is stable or not, you should use the RSSI parameter. When you search for a place to install the GPS tracker, you should calculate the average RSSI (Received Signal Strength Indicator) by taking into account the 10 or more measurements of the RSSI taken over the course of 2-3 minutes while the engine of the vehicle is running and all electronics inside the cab and around the vehicle are switched on.

ARSLAN: /* Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLA Scan settings) */

2026-03-04T10:09:37Z

Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLA Scan settings)

← Older revision		Revision as of 13:09, 4 March 2026
Line 17:		Line 17:
	\|}		\|}

	== Bluetooth and Bluetooth 4.0 tabs (entering MAC address, ~~BLA~~ Scan settings) ==		== Bluetooth and Bluetooth 4.0 tabs (entering MAC address, BLE Scan settings) ==
	In the Teltonika configurator, go to the '''Bluetooth''' tab first. Make sure that everything is configured as shown on the figure below		In the Teltonika configurator, go to the '''Bluetooth''' tab first. Make sure that everything is configured as shown on the figure below

ARSLAN: /* Lost Connection */

2026-03-04T10:09:01Z

Lost Connection

Show changes

ANATOLYI: /* Connecting BLE via adapter (BLE-Rs485 base) */

2026-02-19T11:44:37Z

Connecting BLE via adapter (BLE-Rs485 base)

← Older revision		Revision as of 14:44, 19 February 2026
Line 223:		Line 223:
	[[File:Photo 5418063427176959131 x.jpg]]		[[File:Photo 5418063427176959131 x.jpg]]

	[[File:~~Imageacas~~.png]]		[[File:Таблица данных на телтонику.png]]

	Fig. 22 io_ list (partial)		Fig. 22 io_ list (partial)

ARSLAN at 14:10, 16 January 2026

2026-01-16T14:10:16Z

← Older revision		Revision as of 17:10, 16 January 2026
Line 1:		Line 1:
	[[es:TD-BLE]]		[[es:TD-BLE]]

	= <big>'''~~Qiuck~~ start: Connecting Escort BLE sensors to Teltonika trackers via Bluetooth'''</big> =		= <big>'''Quick start: Connecting Escort BLE sensors to Teltonika trackers via Bluetooth'''</big> =

	= Direct BT connection (no adapter) =		= Direct BT connection (no adapter) =

ANATOLYI: /* Presets */

2026-01-15T07:31:39Z

Presets

← Older revision		Revision as of 10:31, 15 January 2026
Line 287:		Line 287:
	You can also downolad our '''TD 150 BLE''' and '''DU BLE''' presets for Teltonika tracker manually		You can also downolad our '''TD 150 BLE''' and '''DU BLE''' presets for Teltonika tracker manually

	# First of all, download preset file from the links below: [https://drive.google.com/file/d/1_wiyNRlUvUn0JarXYwcJNpeahZNlH1Fw/view TD 150 BLE] [https://drive.google.com/file/d/1xQgTjlbQ8W2oOb8Owpj2Jr_U7xh4-2a0/view DU BLE]2.Follow the Teltonika settings in the right corner below in the configurator [[File:Imageaaveda.png\|833x833px]] 3. Open Preset Settings and find preset file, that you downloaded earlier [[File:Imageacacac.png\|839x839px]] 4. Choose the downloaded preset file [[File:Imagecavcf.png\|837x837px]] [[File:Imageavdsfbdn.png\|837x837px]] 5. After that you will find our preset file in the preset list [[File:Imageacevsd.png\|837x837px]]		# First of all, download preset file from the links below: [https://drive.google.com/file/d/1_wiyNRlUvUn0JarXYwcJNpeahZNlH1Fw/view TD 150 BLE] [https://drive.google.com/file/d/1xQgTjlbQ8W2oOb8Owpj2Jr_U7xh4-2a0/view DU BLE]
			# .Follow the Teltonika settings in the right corner below in the configurator [[File:Imageaaveda.png\|833x833px]]
			# Open Preset Settings and find preset file, that you downloaded earlier [[File:Imageacacac.png\|839x839px]]
			# Choose the downloaded preset file [[File:Imagecavcf.png\|837x837px]] [[File:Imageavdsfbdn.png\|837x837px]]
			# After that you will find our preset file in the preset list [[File:Imageacevsd.png\|837x837px]]

	= Compatibility list =		= Compatibility list =

ANATOLYI: /* Presets */

2026-01-15T07:30:23Z

Presets

← Older revision		Revision as of 10:30, 15 January 2026
Line 287:		Line 287:
	You can also downolad our '''TD 150 BLE''' and '''DU BLE''' presets for Teltonika tracker manually		You can also downolad our '''TD 150 BLE''' and '''DU BLE''' presets for Teltonika tracker manually

	# First of all, download preset file from the links below: [https://drive.google.com/file/d/1_wiyNRlUvUn0JarXYwcJNpeahZNlH1Fw/view TD 150 BLE] [https://drive.google.com/file/d/1xQgTjlbQ8W2oOb8Owpj2Jr_U7xh4-2a0/view DU BLE]2.Follow the Teltonika settings in the right corner below in the configurator [[File:Imageaaveda.png\|833x833px]] 3. Open Preset Settings and find preset file, that you downloaded earlier [[File:Imageacacac.png\|839x839px]] 4. Choose the downloaded preset file [[File:Imagecavcf.png\|837x837px]] [[File:Imageavdsfbdn.png\|837x837px]]5. After that you will find our preset file in the preset list [[File:Imageacevsd.png\|837x837px]]		# First of all, download preset file from the links below: [https://drive.google.com/file/d/1_wiyNRlUvUn0JarXYwcJNpeahZNlH1Fw/view TD 150 BLE] [https://drive.google.com/file/d/1xQgTjlbQ8W2oOb8Owpj2Jr_U7xh4-2a0/view DU BLE]2.Follow the Teltonika settings in the right corner below in the configurator [[File:Imageaaveda.png\|833x833px]] 3. Open Preset Settings and find preset file, that you downloaded earlier [[File:Imageacacac.png\|839x839px]] 4. Choose the downloaded preset file [[File:Imagecavcf.png\|837x837px]] [[File:Imageavdsfbdn.png\|837x837px]] 5. After that you will find our preset file in the preset list [[File:Imageacevsd.png\|837x837px]]

	= Compatibility list =		= Compatibility list =